Lumenier LUX H7 HD Ultimate Flight Controller Lumenier LUX H7 HD Ultimate Flight Controller Catalyst Machineworks About this product The Lumenier LUX H7 HD Ultimate Flight Controller is the most advanced and most powerful flight controller from Lumenier yet! It uses a blazing fast H7 processor along with premium hardware components. Unleash the capabilities of your Cinema (Cine-Lifter) drone or FPV Racing Quadcopter with the Lumenier LUX H7 Ultimate Flight Controller. The LUX H7 is packed full of features like dual gyros, dual 4in1 esc plugs, 13 PWM outputs, dual camera support, BEC 9V power for DJI Air unit, Blackbox logging, and so much more! The LUX H7 builds on all the best features of its F7 predecessor and further improves on hardware components and layout. You get an incredible 7x dedicated UART ports with built-in inversion for peripherals, along with an SD Card slot for practically unlimited data logging. In addition, the LUX H7 can connect up to 13 PWM signals at once! That means it can easily support an Octo-copter, X8, or something even more creative with up to 13 PWM outputs. Eight of these outputs are plug-and-play ready with dual 4in1 ESC connectors right on the flight controller. Dual 4in1 ESC stacks + FC is super simple and clean now with the plug and play configuration. The integrated BetaFlight OSD makes it super simple to display important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more. Going digital instead? No problem, simply output the OSD data via an open UART such as the integrated TX3/RX3 on the plug and play harness for DJI FPV Air Unit. The features don't stop there! The LUX H7 has the ability to run 2 analog camera signals, with a built switching ability. This means you can run 2 cameras simultaneously and assign a switch via the PINIO feature in Betaflight to alternate between the 2 feeds at the flip of a switch. Installing a front and rear camera has never been easier! Have you ever been in an FPV race where you need to plug in your quad, but you don't want to broadcast an FPV signal to knock your friends out of the air? Or how about you crash, and need to save your VTX from burning up while baking in the hot sun. With the LUX H7 you can remotely turn your VTX on or off via a switch on your radio! The LUX features an on-board 3A 9V regulated power pad designed to power your video transmitter (Like DJI FPV Air Unit). Using the PINIO resource, you can assign this pad to a switch on your radio, remotely controlling the power source to your video transmitter. Long range quad and FPV plane pilots will also love the Lumenier LUX H7. It has all the features you need to take full advantage of the long range and autonomous flight technology. The LUX H7 has an on-board barometer, buzzer pad, I2C pad, Ardupilot support, iNAV support (coming soon), GPS/compass pads, and up to 13 PWM inputs S1-S12 +LED for a ton of servo and motor control. The Lumenier LUX H7 Ultimate is a very low profile board allowing it to be mounted in a variety of ways. Signal wires can be soldered directly to the break-out pads to save on size and weight or use the included plug and play cables. The LUX supports PPM or Serial RX (including FrSky, S.BUS, DSMX, etc.).  Features MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash IMU: MPU6000 (SPI1) & ICM20602 (SPI4) Baro: Infineon DPS310 (I2C2) OSD: AT7456E (SPI2) Blackbox: MicroSD card socket (SDIO) 7x UARTs (1,2,3,4,6,7,8) with built-in inversion. 13x PWM outputs(including “LED” pad) 2x I2C ports 1x CAN bus 6x ADC USB Type-C (USB2.0) 2x JST-SH1.0_8pin connector for 4in1 ESC 1x JST-SH1.0_8pin connector for DJI FPV Air Unit Dual Camera Inputs switch 9V ON/OFF switch Vbat Input: 6~36V (2~8S LiPo) BEC 5V 2A cont. (Max.3A) BEC 9V 2A cont. (Max.3A) Specifications High quality, gold plated PCB USB C connector for programming Dimensions: 36x36x6mm (includes USB in height) Mounting Holes: 30.5mm square to center of holes  Weight: 7g Firmware Targets BetaFlight: MATEKH743 (v4.3 and above) ArduPilot: MATEKH743 iNav: MATEKH743 Dimensions Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm Dimensions: 36 x 36 x 5 mm Manual Download the Lumenier LUX H7 HD User Manual Firmware Download Betaflight Configurator - Latest Betaflight Firmware (LUX H7 is supported in 4.3 and above) Find the latest stable build of BF 4.3 here The LUX H7 HD comes with a customized version of BF 4.2.8 from the factory Download the custom LUX H7 HD BetaFlight 4.2.8 .hex here Download the custom LUX H7 HD BetaFlight 4.2.9 .hex here  ArduPilot Target MATEKH743 https://firmware.ardupilot.org/Plane/stable/MatekH743/ https://firmware.ardupilot.org/Copter/stable/MatekH743/ Youtube Installing ArduPilot on an H743 Flight Controller ICM42605+MPU6000 instead of ICM20602+MPU6000 on H743-SLIM V1.5/ H743-mini V1.5/H743-WING V2. If ICM42605 can’t be probed with ArduPilot 4.1, set INS_ENABLE_MASK to 7 or default 127. INAV inav_3.0.2_MATEKH743 inav_4.0.0_MATEKH743 MPU6000, default ICM20602, set gyro_to_use = 1, set acc_hardware = MPU6500 ICM42605, set gyro_to_use = 2, set acc_hardware = icm42605 BetaFlight Target MATEKH743 betaflight_4.2.8_MATEKH743 betaflight_4.2.9_MATEKH743 betaflight_4.2.10_MATEKH743 betaflight_4.2.10_MATEKH743_426XX.hex for H743-SLIM V1.5, H743-mini V1.5, H743-WING V2 betaflight_4.3.0RC1_MATEKH743_426XX.hex for H743-SLIM V1.5, H743-mini V1.5, H743-WING V2 betaflight_4.3.0RC2_MATEKH743_426XX.hex for H743-SLIM V1.5, H743-mini V1.5, H743-WING V2 Note: There is a known bug with BF 4.2.xx on this board related to M7 output and bi-directional dshot. We suggest downloading the latest stable release of 4.3 which fixes this issue.  Find the latest stable build of BF 4.3 here (download MATEKH743 hex file)  

Lumenier LUX H7 HD Ultimate Flight Controller

Code: CM02420
$119.99
In Stock
Add to Wishlist Add to Compare


About this product

The Lumenier LUX H7 HD Ultimate Flight Controller is the most advanced and most powerful flight controller from Lumenier yet! It uses a blazing fast H7 processor along with premium hardware components. Unleash the capabilities of your Cinema (Cine-Lifter) drone or FPV Racing Quadcopter with the Lumenier LUX H7 Ultimate Flight Controller. The LUX H7 is packed full of features like dual gyros, dual 4in1 esc plugs, 13 PWM outputs, dual camera support, BEC 9V power for DJI Air unit, Blackbox logging, and so much more!

Lumenier LUX H7 Ultimate Flight Controller

The LUX H7 builds on all the best features of its F7 predecessor and further improves on hardware components and layout. You get an incredible 7x dedicated UART ports with built-in inversion for peripherals, along with an SD Card slot for practically unlimited data logging. In addition, the LUX H7 can connect up to 13 PWM signals at once! That means it can easily support an Octo-copter, X8, or something even more creative with up to 13 PWM outputs. Eight of these outputs are plug-and-play ready with dual 4in1 ESC connectors right on the flight controller. Dual 4in1 ESC stacks + FC is super simple and clean now with the plug and play configuration.

The integrated BetaFlight OSD makes it super simple to display important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more. Going digital instead? No problem, simply output the OSD data via an open UART such as the integrated TX3/RX3 on the plug and play harness for DJI FPV Air Unit.

The features don't stop there! The LUX H7 has the ability to run 2 analog camera signals, with a built switching ability. This means you can run 2 cameras simultaneously and assign a switch via the PINIO feature in Betaflight to alternate between the 2 feeds at the flip of a switch. Installing a front and rear camera has never been easier!

Have you ever been in an FPV race where you need to plug in your quad, but you don't want to broadcast an FPV signal to knock your friends out of the air? Or how about you crash, and need to save your VTX from burning up while baking in the hot sun. With the LUX H7 you can remotely turn your VTX on or off via a switch on your radio! The LUX features an on-board 3A 9V regulated power pad designed to power your video transmitter (Like DJI FPV Air Unit). Using the PINIO resource, you can assign this pad to a switch on your radio, remotely controlling the power source to your video transmitter.

Long range quad and FPV plane pilots will also love the Lumenier LUX H7. It has all the features you need to take full advantage of the long range and autonomous flight technology. The LUX H7 has an on-board barometer, buzzer pad, I2C pad, Ardupilot support, iNAV support (coming soon), GPS/compass pads, and up to 13 PWM inputs S1-S12 +LED for a ton of servo and motor control.

The Lumenier LUX H7 Ultimate is a very low profile board allowing it to be mounted in a variety of ways. Signal wires can be soldered directly to the break-out pads to save on size and weight or use the included plug and play cables. The LUX supports PPM or Serial RX (including FrSky, S.BUS, DSMX, etc.). 

Lumenier LUX H7 Ultimate Flight Controller

Features

  • MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash
  • IMU: MPU6000 (SPI1) & ICM20602 (SPI4)
  • Baro: Infineon DPS310 (I2C2)
  • OSD: AT7456E (SPI2)
  • Blackbox: MicroSD card socket (SDIO)
  • 7x UARTs (1,2,3,4,6,7,8) with built-in inversion.
  • 13x PWM outputs(including “LED” pad)
  • 2x I2C ports
  • 1x CAN bus
  • 6x ADC
  • USB Type-C (USB2.0)
  • 2x JST-SH1.0_8pin connector for 4in1 ESC
  • 1x JST-SH1.0_8pin connector for DJI FPV Air Unit
  • Dual Camera Inputs switch
  • 9V ON/OFF switch
  • Vbat Input: 6~36V (2~8S LiPo)
  • BEC 5V 2A cont. (Max.3A)
  • BEC 9V 2A cont. (Max.3A)

Specifications

  • High quality, gold plated PCB
  • USB C connector for programming
  • Dimensions: 36x36x6mm (includes USB in height)
  • Mounting Holes: 30.5mm square to center of holes 
  • Weight: 7g

Firmware Targets

  • BetaFlight: MATEKH743 (v4.3 and above)
  • ArduPilot: MATEKH743
  • iNav: MATEKH743

Dimensions

  • Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
  • Dimensions: 36 x 36 x 5 mm

Manual

Firmware

ArduPilot Target MATEKH743

INAV

BetaFlight Target MATEKH743

Note: There is a known bug with BF 4.2.xx on this board related to M7 output and bi-directional dshot. We suggest downloading the latest stable release of 4.3 which fixes this issue.  Find the latest stable build of BF 4.3 here (download MATEKH743 hex file)

 


About this product

The Lumenier LUX H7 HD Ultimate Flight Controller is the most advanced and most powerful flight controller from Lumenier yet! It uses a blazing fast H7 processor along with premium hardware components. Unleash the capabilities of your Cinema (Cine-Lifter) drone or FPV Racing Quadcopter with the Lumenier LUX H7 Ultimate Flight Controller. The LUX H7 is packed full of features like dual gyros, dual 4in1 esc plugs, 13 PWM outputs, dual camera support, BEC 9V power for DJI Air unit, Blackbox logging, and so much more!

Lumenier LUX H7 Ultimate Flight Controller

The LUX H7 builds on all the best features of its F7 predecessor and further improves on hardware components and layout. You get an incredible 7x dedicated UART ports with built-in inversion for peripherals, along with an SD Card slot for practically unlimited data logging. In addition, the LUX H7 can connect up to 13 PWM signals at once! That means it can easily support an Octo-copter, X8, or something even more creative with up to 13 PWM outputs. Eight of these outputs are plug-and-play ready with dual 4in1 ESC connectors right on the flight controller. Dual 4in1 ESC stacks + FC is super simple and clean now with the plug and play configuration.

The integrated BetaFlight OSD makes it super simple to display important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more. Going digital instead? No problem, simply output the OSD data via an open UART such as the integrated TX3/RX3 on the plug and play harness for DJI FPV Air Unit.

The features don't stop there! The LUX H7 has the ability to run 2 analog camera signals, with a built switching ability. This means you can run 2 cameras simultaneously and assign a switch via the PINIO feature in Betaflight to alternate between the 2 feeds at the flip of a switch. Installing a front and rear camera has never been easier!

Have you ever been in an FPV race where you need to plug in your quad, but you don't want to broadcast an FPV signal to knock your friends out of the air? Or how about you crash, and need to save your VTX from burning up while baking in the hot sun. With the LUX H7 you can remotely turn your VTX on or off via a switch on your radio! The LUX features an on-board 3A 9V regulated power pad designed to power your video transmitter (Like DJI FPV Air Unit). Using the PINIO resource, you can assign this pad to a switch on your radio, remotely controlling the power source to your video transmitter.

Long range quad and FPV plane pilots will also love the Lumenier LUX H7. It has all the features you need to take full advantage of the long range and autonomous flight technology. The LUX H7 has an on-board barometer, buzzer pad, I2C pad, Ardupilot support, iNAV support (coming soon), GPS/compass pads, and up to 13 PWM inputs S1-S12 +LED for a ton of servo and motor control.

The Lumenier LUX H7 Ultimate is a very low profile board allowing it to be mounted in a variety of ways. Signal wires can be soldered directly to the break-out pads to save on size and weight or use the included plug and play cables. The LUX supports PPM or Serial RX (including FrSky, S.BUS, DSMX, etc.). 

Lumenier LUX H7 Ultimate Flight Controller

Features

  • MCU: STM32H743VIT6, 480MHz , 1MB RAM, 2MB Flash
  • IMU: MPU6000 (SPI1) & ICM20602 (SPI4)
  • Baro: Infineon DPS310 (I2C2)
  • OSD: AT7456E (SPI2)
  • Blackbox: MicroSD card socket (SDIO)
  • 7x UARTs (1,2,3,4,6,7,8) with built-in inversion.
  • 13x PWM outputs(including “LED” pad)
  • 2x I2C ports
  • 1x CAN bus
  • 6x ADC
  • USB Type-C (USB2.0)
  • 2x JST-SH1.0_8pin connector for 4in1 ESC
  • 1x JST-SH1.0_8pin connector for DJI FPV Air Unit
  • Dual Camera Inputs switch
  • 9V ON/OFF switch
  • Vbat Input: 6~36V (2~8S LiPo)
  • BEC 5V 2A cont. (Max.3A)
  • BEC 9V 2A cont. (Max.3A)

Specifications

  • High quality, gold plated PCB
  • USB C connector for programming
  • Dimensions: 36x36x6mm (includes USB in height)
  • Mounting Holes: 30.5mm square to center of holes 
  • Weight: 7g

Firmware Targets

  • BetaFlight: MATEKH743 (v4.3 and above)
  • ArduPilot: MATEKH743
  • iNav: MATEKH743

Dimensions

  • Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
  • Dimensions: 36 x 36 x 5 mm

Manual

Firmware

ArduPilot Target MATEKH743

INAV

BetaFlight Target MATEKH743

Note: There is a known bug with BF 4.2.xx on this board related to M7 output and bi-directional dshot. We suggest downloading the latest stable release of 4.3 which fixes this issue.  Find the latest stable build of BF 4.3 here (download MATEKH743 hex file)