WhoopMaster 4" WhoopMaster 4" Catalyst Machineworks “REMOVE PROPS BEFORE CONNECTING TO BETAFLIGHT/INAV, BENCH TESTING, OR SETUP” Do you even whoop bro?! Meet the WhoopMaster 4 Inch. A new take on a well established drone genre in the FPV universe. There are only a couple thousand different offerings in the market for those pilots looking to get their "whoop" on, so what makes this creation from the Catalyst special? The motivation for this bird was born from our never ending desire to do things differently. We want to bring a whoop to the world that has some special abilities and 'pizazz' not yet seen in the market. First off this is a 4" Cinewhoop. If you look around and do your research you will find there are very few offerings in this size. Most popular whoops max out around 3.5" props. It doesn't sound like much but that extra 1/2" affords a decent amount of thrust headroom and ability to confidently carry extra payload. The larger layout translates to super smooth control resolution for premium proximity flying while still giving a pilot the ability to cruise at faster speeds if needed. The WhoopMaster has the ability to carry a full sized GoPro front or rear. This means the camera's vantage point can be located facing forward or facing backwards. A backwards facing camera gives you a whole new set of shots to experiment with in your edit. The WhoopMaster has the capability to be built up as an "all weather" rig. This is made possible with optional components that incase the ESC, FC, VTX, and receiver in nearly waterproof enclosure(s). 7075 machined aluminum heat sink components allow heat from the ESC/VTX to escape the enclosure. What else is different about this bird? It looks cool AF, and YES that matters.  Included in the 3D Parts Kit:  DJI Original HD FPV camera mount set x 1 Caddx Vista / Runcam Link FPV Antenna Mount x 1 Caddx Vista / Runcam Link FPV VTX Mount x 1 Full size gopro mount + hardware set x 1 Where do I buy accessories? ALL WEATHER UPGRADE  SOFT ARM BUMPERS  OPTIONAL 3D PARTS MISC. OPTIONAL PARTS  Frame Features:  Large 4" props to carry extra payload Run a full sized Gopro facing forward or backwards  Near waterproof "all weather" options available  Large top deck allowing you to run BIG lipos (up to 1800mah 6s) Crash tough carbon prop guards Optional soft prop guard bumpers available  Easy to build Build with micro stack or AIO "Whoop" FC/ESC Easy to maintain  Super rigid frame structure helping with "tunability"  Build with HD or analog FPV Integrated panel mount XT60 connector  Integrated hole for SMA FPV antennas (antenna sold separate) Lots of 3D printed accessories available to facilitate many different electronics combos Industry leading carbon fiber High strength steel and aircraft grade 7075 aluminum fasteners Available as a frame kit or full custom BNF (email info@catalystmachineworks.com to get your build started!)  Soft bumpers not included Gopro not included Electronics not included   Frame Specs: Standard Frame Weight (w/FPV camera mount parts): 147g approximate Frame Size: 167mm  Prop Size: 4"  Carbon Fiber: Twill Weave 3K Matte Arm carbon thickness: 2.5mm Top plate carbon thickness: 1.5mm Bottom plate carbon thickness: 1mm Cage carbon front, side, and rear attachment bits: 4mm Cage carbon guards: 1.5mm (doubled up) Cage top carbon guards: 1.5mm Camera Angle Range: 0 - 65 degrees Motors supported: 2306, 2207, 2206, 2205.5, 2205 (see motor sizing requirements graphic below!) Motor bell can be no larger than 30mm diameter Distance from motor base to motor bell prop seat can be no shorter than 16.5mm Lipos supported: 3s, 4s, 5s, 6s (up to 1800mah 6s) Lipo mounting position: Top Fastener Material: High quality steel and 7075 aluminum Standoff material: Aluminum  Accepted ESC/FC: (micro 20mm x 20mm, whoop AIO 25.5mm x 25.5mm) THE WHOOPMASTER 4" WILL NOT FIT FULL SIZED FC/ESC STACKS! Standard frame motor pad mounting holes: M3 screws on 16mm circle or M2 screws on 12mm circle Supported FPV cameras: Micro, Nano, or Mini Accepts the Caddx vista HD FPV VTX Accepts the RunCam Link Phoenix HD FPV Camera Kit Accepts analog VTX offerings Accepts Fat Shark 'Shark Byte' HD FPV systems All weather enclosure will only accept Caddx Vista or RunCam Link! All weather enclosure will only accept 20x20 micro FC/ESC stacks BILL OF MATERIAL (PARTS LIST) ACCESSORIES  SPARE PARTS FRAME ASSEMBLY VIDEO               

WhoopMaster 4"

Code: CM02030

“REMOVE PROPS BEFORE CONNECTING TO BETAFLIGHT/INAV, BENCH TESTING, OR SETUP”





Do you even whoop bro?! Meet the WhoopMaster 4 Inch. A new take on a well established drone genre in the FPV universe. There are only a couple thousand different offerings in the market for those pilots looking to get their "whoop" on, so what makes this creation from the Catalyst special? The motivation for this bird was born from our never ending desire to do things differently. We want to bring a whoop to the world that has some special abilities and 'pizazz' not yet seen in the market. First off this is a 4" Cinewhoop. If you look around and do your research you will find there are very few offerings in this size. Most popular whoops max out around 3.5" props. It doesn't sound like much but that extra 1/2" affords a decent amount of thrust headroom and ability to confidently carry extra payload. The larger layout translates to super smooth control resolution for premium proximity flying while still giving a pilot the ability to cruise at faster speeds if needed. The WhoopMaster has the ability to carry a full sized GoPro front or rear. This means the camera's vantage point can be located facing forward or facing backwards. A backwards facing camera gives you a whole new set of shots to experiment with in your edit. The WhoopMaster has the capability to be built up as an "all weather" rig. This is made possible with optional components that incase the ESC, FC, VTX, and receiver in nearly waterproof enclosure(s). 7075 machined aluminum heat sink components allow heat from the ESC/VTX to escape the enclosure. What else is different about this bird? It looks cool AF, and YES that matters. 

Included in the 3D Parts Kit: 

  1. DJI Original HD FPV camera mount set x 1
  2. Caddx Vista / Runcam Link FPV Antenna Mount x 1
  3. Caddx Vista / Runcam Link FPV VTX Mount x 1
  4. Full size gopro mount + hardware set x 1

Where do I buy accessories?

Frame Features: 

  • Large 4" props to carry extra payload
  • Run a full sized Gopro facing forward or backwards 
  • Near waterproof "all weather" options available 
  • Large top deck allowing you to run BIG lipos (up to 1800mah 6s)
  • Crash tough carbon prop guards
  • Optional soft prop guard bumpers available 
  • Easy to build
  • Build with micro stack or AIO "Whoop" FC/ESC
  • Easy to maintain 
  • Super rigid frame structure helping with "tunability" 
  • Build with HD or analog FPV
  • Integrated panel mount XT60 connector 
  • Integrated hole for SMA FPV antennas (antenna sold separate)
  • Lots of 3D printed accessories available to facilitate many different electronics combos
  • Industry leading carbon fiber
  • High strength steel and aircraft grade 7075 aluminum fasteners
  • Available as a frame kit or full custom BNF (email info@catalystmachineworks.com to get your build started!) 
  • Soft bumpers not included
  • Gopro not included
  • Electronics not included

 

Frame Specs:

  • Standard Frame Weight (w/FPV camera mount parts): 147g approximate
  • Frame Size: 167mm 
  • Prop Size: 4" 
  • Carbon Fiber: Twill Weave 3K Matte
  • Arm carbon thickness: 2.5mm
  • Top plate carbon thickness: 1.5mm
  • Bottom plate carbon thickness: 1mm
  • Cage carbon front, side, and rear attachment bits: 4mm
  • Cage carbon guards: 1.5mm (doubled up)
  • Cage top carbon guards: 1.5mm
  • Camera Angle Range: 0 - 65 degrees
  • Motors supported: 2306, 2207, 2206, 2205.5, 2205 (see motor sizing requirements graphic below!)
  • Motor bell can be no larger than 30mm diameter
  • Distance from motor base to motor bell prop seat can be no shorter than 16.5mm
  • Lipos supported: 3s, 4s, 5s, 6s (up to 1800mah 6s)
  • Lipo mounting position: Top
  • Fastener Material: High quality steel and 7075 aluminum
  • Standoff material: Aluminum 
  • Accepted ESC/FC: (micro 20mm x 20mm, whoop AIO 25.5mm x 25.5mm)
  • THE WHOOPMASTER 4" WILL NOT FIT FULL SIZED FC/ESC STACKS!
  • Standard frame motor pad mounting holes: M3 screws on 16mm circle or M2 screws on 12mm circle
  • Supported FPV cameras: Micro, Nano, or Mini
  • Accepts the Caddx vista HD FPV VTX
  • Accepts the RunCam Link Phoenix HD FPV Camera Kit
  • Accepts analog VTX offerings
  • Accepts Fat Shark 'Shark Byte' HD FPV systems
  • All weather enclosure will only accept Caddx Vista or RunCam Link!
  • All weather enclosure will only accept 20x20 micro FC/ESC stacks

BILL OF MATERIAL (PARTS LIST)

ACCESSORIES 

SPARE PARTS

FRAME ASSEMBLY VIDEO 

 



 

 

 

 

 

 


“REMOVE PROPS BEFORE CONNECTING TO BETAFLIGHT/INAV, BENCH TESTING, OR SETUP”





Do you even whoop bro?! Meet the WhoopMaster 4 Inch. A new take on a well established drone genre in the FPV universe. There are only a couple thousand different offerings in the market for those pilots looking to get their "whoop" on, so what makes this creation from the Catalyst special? The motivation for this bird was born from our never ending desire to do things differently. We want to bring a whoop to the world that has some special abilities and 'pizazz' not yet seen in the market. First off this is a 4" Cinewhoop. If you look around and do your research you will find there are very few offerings in this size. Most popular whoops max out around 3.5" props. It doesn't sound like much but that extra 1/2" affords a decent amount of thrust headroom and ability to confidently carry extra payload. The larger layout translates to super smooth control resolution for premium proximity flying while still giving a pilot the ability to cruise at faster speeds if needed. The WhoopMaster has the ability to carry a full sized GoPro front or rear. This means the camera's vantage point can be located facing forward or facing backwards. A backwards facing camera gives you a whole new set of shots to experiment with in your edit. The WhoopMaster has the capability to be built up as an "all weather" rig. This is made possible with optional components that incase the ESC, FC, VTX, and receiver in nearly waterproof enclosure(s). 7075 machined aluminum heat sink components allow heat from the ESC/VTX to escape the enclosure. What else is different about this bird? It looks cool AF, and YES that matters. 

Included in the 3D Parts Kit: 

  1. DJI Original HD FPV camera mount set x 1
  2. Caddx Vista / Runcam Link FPV Antenna Mount x 1
  3. Caddx Vista / Runcam Link FPV VTX Mount x 1
  4. Full size gopro mount + hardware set x 1

Where do I buy accessories?

Frame Features: 

  • Large 4" props to carry extra payload
  • Run a full sized Gopro facing forward or backwards 
  • Near waterproof "all weather" options available 
  • Large top deck allowing you to run BIG lipos (up to 1800mah 6s)
  • Crash tough carbon prop guards
  • Optional soft prop guard bumpers available 
  • Easy to build
  • Build with micro stack or AIO "Whoop" FC/ESC
  • Easy to maintain 
  • Super rigid frame structure helping with "tunability" 
  • Build with HD or analog FPV
  • Integrated panel mount XT60 connector 
  • Integrated hole for SMA FPV antennas (antenna sold separate)
  • Lots of 3D printed accessories available to facilitate many different electronics combos
  • Industry leading carbon fiber
  • High strength steel and aircraft grade 7075 aluminum fasteners
  • Available as a frame kit or full custom BNF (email info@catalystmachineworks.com to get your build started!) 
  • Soft bumpers not included
  • Gopro not included
  • Electronics not included

 

Frame Specs:

  • Standard Frame Weight (w/FPV camera mount parts): 147g approximate
  • Frame Size: 167mm 
  • Prop Size: 4" 
  • Carbon Fiber: Twill Weave 3K Matte
  • Arm carbon thickness: 2.5mm
  • Top plate carbon thickness: 1.5mm
  • Bottom plate carbon thickness: 1mm
  • Cage carbon front, side, and rear attachment bits: 4mm
  • Cage carbon guards: 1.5mm (doubled up)
  • Cage top carbon guards: 1.5mm
  • Camera Angle Range: 0 - 65 degrees
  • Motors supported: 2306, 2207, 2206, 2205.5, 2205 (see motor sizing requirements graphic below!)
  • Motor bell can be no larger than 30mm diameter
  • Distance from motor base to motor bell prop seat can be no shorter than 16.5mm
  • Lipos supported: 3s, 4s, 5s, 6s (up to 1800mah 6s)
  • Lipo mounting position: Top
  • Fastener Material: High quality steel and 7075 aluminum
  • Standoff material: Aluminum 
  • Accepted ESC/FC: (micro 20mm x 20mm, whoop AIO 25.5mm x 25.5mm)
  • THE WHOOPMASTER 4" WILL NOT FIT FULL SIZED FC/ESC STACKS!
  • Standard frame motor pad mounting holes: M3 screws on 16mm circle or M2 screws on 12mm circle
  • Supported FPV cameras: Micro, Nano, or Mini
  • Accepts the Caddx vista HD FPV VTX
  • Accepts the RunCam Link Phoenix HD FPV Camera Kit
  • Accepts analog VTX offerings
  • Accepts Fat Shark 'Shark Byte' HD FPV systems
  • All weather enclosure will only accept Caddx Vista or RunCam Link!
  • All weather enclosure will only accept 20x20 micro FC/ESC stacks

BILL OF MATERIAL (PARTS LIST)

ACCESSORIES 

SPARE PARTS

FRAME ASSEMBLY VIDEO